New MachinesUsed MachinesSpecialsContact UsSite Map

PDF Brochure




HIGH SPEED LATERAL TO LINEAL FEED TABLE WITH HYDRAULIC INFINITELY VARIABLE FEED RATES TO 600 FPM

FOR CONTINUOUS AUTOMATIC FEEDING OF RANDOM LENGTH STRIPS AND/OR SHORT BLOCK MATERIAL TO MATCHERS OR MOULDERS

TECHNOLOGICALLY ADVANCED HASTRAKTM AUTOMATIC LATERAL ACCELERATION SYSTEM

THE HSLF DOES THE WORK---YOUR OPERATOR DOES THE THINKING

MAKE MONEY WITH SHORTS - INCREASE PRODUCTION - MAXIMIZE GRADE - ALL AT THE SAME TIME

ANOTHER HASKO PROFIT-PUSHING SOLUTION FOR IMPROVED SIDEMATCHER THROUGHPUT AND OVERALL PRODUCT ENHANCEMENT





Product Advantages:

  • Enables Operator to Focus on Turning Stock for Best Face and/or Yield Improvement

  • Continuous "Gap Free" Automatic Feeding into Sidematchers or Moulders

  • Uninterrupted Performance on Random Length and/or Short Block Material

  • Enhances Operator Safety by Placing Him in Area Remote to Pinch Point Hazard

  • Utilizes Unique HastrakTM Lateral Feed System with Positive Top and Bottom Acceleration

  • Improves Sidematcher Throughput by Minimizing Gaps

  • Unequaled High Speed Performance on Random Length and/or Short Block Material

  • Worth Repeating:
    "The Hasko HSLF facilitates improved grade yield by reducing operator (feeder) efforts by automatic gap-free positioning of strips and accelerating them forward without the efforts of the operator



    Capacity:
    Width: 2" (minimum) to 6" (maximum)
    Thickness: 1/2" (minimuim) to 2" (maximum)
    Minimum Length: 10"
    Feed Speeds: Infinitely variable to match moulder through-feeds of 200-400 FPM (standard) or to 600 FPM (optional).

    Rolls:
    (7) Shafts with one 6" diameter X 9" long spiral cast iron lower infeed rolls (HSLF-L) (Long Machine).
    (5) Shafts with one 6" diameter X 9" long spiral cast iron lower infeed rolls (HSLF) (Std. Machine).
    (1) Shaft with one 6" diameter upper ductile iron pineapple roll. (Carbide optional).
    (1) Shaft with one 6" diameter X 2.5" upper knurled and chromed hurry-up roll.
    (1) Shaft with one 4" diameter X 6" wide lower spiral roll before pineapple roll.
    (1) Shaft with one 4" diameter X 9" wide lower spiral roll below pineapple roll.
    (1) Shaft with one 4" diameter x 6" wide lower hurry-up exit roll

    Hydraulics:
    25 H.P. 1800 R.P.M. totally enclosed fan cooled motor.
    30 H.P. 1800 R.P.M. totally enclosed fan cooled motor. (Optional)
    1-1/2 H.P. 1800 R.P.M. totally enclosed fan cooled motor for Accumulation Table (Optional)
    Pump is direct coupled to motor -tank mounted 60-gallon hydraulic reservoir.
    25 (30 optional) gallons per minute at 1750 P.S.I. maximum operating pressure.
    1/4 H.P. fan cooled heat exchange unit.
    Flow valve for 50-575 feet per minute forward (optional to 750).
    Reverse preset at 75 feet per minute.

    Final Drives:
    (1) Hydraulic motor direct coupled to pineapple shaft.
    (1) Hydraulic motor direct coupled top hurry-up roll shaft.
    (1) Hydraulic motor direct coupled to lower linear feed spiral roll. (Remaining lower rolls driven via "V"-belts with take-up idlers.)
    (1) Hydraulic motor direct coupled to lateral feed chain fence (Board Guide Unit)
    Lateral deck chains are chain-driven through a heavy duty gear reducer coupled to a hydraulic motor.
    Top lateral hold-down chains are "V"-belt driven through a gear reducer coupled to hydraulic motor.

    Electrical:
    Nema 12 enclosures, with magnetic relays and controls for 460/60/3 voltage (standard). (Others, optional)
    All control circuitry is 110 volt.
    PLC (programmable logic controller) functions.
    Hydraulic unit and electrical panel locations other than standard floor plan are optional.

    Pneumatics:
    Top rolls are each air tensioned via 2-1/2" X 3-1/2" cylinders and individual regulators using 7-18 P.S.I. lift pressure.
    The hold-down unit is air tensioned via a 4" x 4" stroke.
    Four-way, two-position valves raise and lower rolls & lateral top hold-down unit.
    All regulators, filters, and lubricators are mounted on machine.

    Dimensions and Weights (Overall and Approximate):
    Standard Machine: 15.5' long x 8.75' wide x 6' high, appx. 5200 lbs.
    Long Machine: 19.5' long x 8.75' wide x 6' high, appx. 5500 lbs.
    Hydraulic Unit Weight: Approximately 1150 lbs. (with oil)
    Accumulation Table: Optional, sized to customer application

    The New Hasko HSLF will Free Your Operator to Make Intelligent Decisions and Greatly Improve Overall Product Grade.

    THAT'S WHAT HASKO REFERS TO AS "A PROFIT-PUSHING SOLUTION !"